In the building sector Airpol meets its clients’ needs in terms of environmental protection, efficiency enhancing and living confort. This vision is supported by the technical performances of its products, that ensure building, management and maintenance cost savings, in addition to high quality structural and aesthetic results.
-
airSLAB / lightening element for flat or inclined slabs
- Applications
- in-situ joist
- support on pre-cast joist
- in-situ joist with under-joist flaps
-
airSTILL / EPS printed panels
This insulating panels are characterized by a low water-vapour absorption, that improves thermal efficiency: they are ideal for insulating buildings’ basements, foundations, roofs and cavities.
Panels are available in numerous versions: some of them are normally available in prompt delivery, others are produced on customer’s request. The standard version is sharp-edged (rebated on four sides on demand) and white with addition of graphite.
Panels with the same general features but with different surface are also available: rough surfaces increase the adhesion of thermal overcoats.
- Applications
- vertical cavities
- attics
- false ceilings
- external coats
- coverings
- underfloor heating
-
airLAST / EPS insulation panels cut from a block
These panels are obtained from expanded polystyrene sintering and they undergo continuous and constant quality control. Perfect for the thermal insulation of buildings, even when moderate resistance to compression is required.
EPS insulation panels are produced according to UNI EN 13163 and their quality is certified: each parcel comes with identity label and warranty.
- Applications
- vertical cavities
- attics
- false ceilings
- external coats
- coverings
- underfloor heating
-
airPOR / cut from a block insulation panels in EPS with addiction of graphite
This panel offers superb mechanical performance, dimensional stability and a remarkable degree of breathability. Coupled to any material which allows water-vapour exchange, it assures hygiene and perfect thermal insulation.
Thanks to the addition of graphite, density being equal, thermal conductivity increases of 0,005W/mk if compared to a white panel.
Therefore, it is required less raw material to obtain the same performance of a normal EPS. The reduction of thermal conductivity also allows the use of thinner panels, to the benefit of perimeter volume reduction of walls, roofs and floors.
-
airTOP / monodirectional under-tile
Closed-cells thermo-insulating panel (rebated on four sides) made of EPS, white/graphite colour, self-extinguishing with euroclass E reaction to fire, CE marking, compliant with the UNI EN 13163, coupled with a multilayer wooden slat housed in the middle.
-
airTEG / EPS microventilated under-tile
White/graphite thermoinsulating panel with Euroclass E reaction to fire, compliant with the UNI EN 13163 and with quality markings IIP-UNI/CE, rebated on four sides.
Available in variable dimentions, suitable for any roof tiles; its crossed canals allow ventilation, lowering temperature in summer and reducing humidity in winter.
-
airWIND / for roofs insulation and ventilation
System for insulation and mono/birectional roof ventilation; it is composed by an expanded sintered polystyrene panel, compliant with Uni EN 13163 and CE marking, Euroclass E reaction to fire, coupled with an OSB panel of variable thickness from 9 to 12 mm.
This system is suitable for any kind of gable roof, which requires high thermal insulation and ventilation or microventilation. It can be made with a variable ventilation chamber created by the panel spacers, where OBS is housed, depending on the required ventilation thickness.
The possibility to vary the thickness of insulation panel and ventilation chamber makes this system suitable for any climate zone and for any kind of gable roof.
-
airTHERM / lightweight aggregate
Composed by properly treated EPS particles that can be uniformly mixed, with no risk of pieces separation or floating.
This new material is different from traditional ones, since its thermo-insulating properties are similar to a pure insulating material, with much better adhesiveness properties.
- Applications
- Light insulating underfloors for civil, agricultural andindustrial purposes
- Insulating screed for coverings and attics
- Light screeds for slopes creation on flat roofs and terraces
- Light filling for corrugated sheets covers
-
airPROV / cubic container for concrete samples
Made of expanded sintered polystyrene, it is used for concrete samples containers.
Composed by two elements: the base, whose internal size is 150x150x150 and the lid, to garantee hermetic distance.
The thermal properties of sintered expanded polystyrene avoid concrete thermal changes in the hardening process, therefore ensuring a gradual humidity release and a perfect drying process.
-
airBLOCK / EPS parallelepiped
Used for rectangular section ground beam foundations, made on demand depending on the surface to cover. Suitable for any kind of substrate: soil, scree, lean concrete.
Its advantages are: reduction of the load transmitted to the ground; single concrete pouring for beams and screed (the blocks work as framework); elimination of filling material compactation. Reduction of concrete quantities used for screed, due both to the absence of concrete leakage and to the planarity of the external concrete floor area during the laying phase. No humidity from the ground.
The mentioned advantages assure cost savings in contruction, rapid installation and elimination of the framework for the concrete laying.
English
Italian